Electrical

The latest version of the famous Battery Tender®. Lucky for you (and your battery) the cost is the same. The enhancements to the original design are in the circuitry that ensures better charge absorption and a built-in 72 hour safety timer to protect a marginal battery from being overcharged. The display improvements tell the user that AC power is on, when it is charging, that the battery is 80% charged, that full charge has been attained, and when the unit is in “float” charge mode. Electrifying.12V, 1.25A.

Nice and hefty for jumping a motorcycle or other light vehicles. Durable clamps grab battery posts with authority. Made of 10 gauge polar/solar wire that stays flexible. May be just the thing to save that ride. 6'. Includes storage bag.

Know the health of your bikes charging system in real-time with this compact, waterproof, digital voltmeter. Reads tenths of a volt (12.6, 12.7, 12.8, etc) and is easy to install. Compact, easy to read, waterproof, vibration proof and dust proof.

Install with permanent double-sided mounting adhesive tape to attach to the side an instrument panel, triple clamp or fairing or use the removable (file or grind off) bosses for bolt-on dashboard installations.

Connect to any circuit that’s powered when your bikes’ key is in the ‘run’ position and you’ll see the battery’s voltage. Then hit the starter and the display will indicate the a slight voltage drop as the engine cranks over. And you’ll notice similar tenth-of-a-volt electrical fluctuations whenever a brake light, driving light, electric grips, horn or other electric load is added, and a correctly functioning charging system will stabilize the readout nearly instantaneously. Reassuring. But if you notice the system voltage is for some reason slowly dropping you’ve either added too much load, or the charging system isn’t working right, which is nice to know before unexpectedly finding yourself on the side of the road somewhere. Most bikes will run for some time if the charging system fails, so you can get to someplace better than a lonely roadside. A café, bike shop, motel, or home. Inexpensive peace of mind for the electrically paranoid.

Installation notes: Shortish 6” leads mean you’ll probably need add a bit of wire for most installations, and the display is bright enough to be read easily in direct sunlight so it may be overly bright at night…which can be adjusted/dimmed with nail polish or a thin fog of overspray. Specify Red, Green or Blue display color. Measures voltage from 3.5 to 30V. 1”x.6”x.7”.

A simple, lightweight, highly accurate way to measure and monitor the battery on your bike. Easy to install, too. Simply plug this indicator into an SAE connector hooked directly to your battery (sold separately) and the LCD displays voltage when the button is pressed or when initially plugged in. Works with any 12V Flooded, AGM and Gel batteries. Displays voltage range from 3V to 16V within +/-0.1 volt accuracy. Colored lights also illuminate red, yellow or green to indicate battery health.

Super-high density oxide plate design combined with NanoGel Electrolyte technology increases surface area, giving superior cranking amps, quicker charging, more power, less sulphation and twice the life expectancy of traditional batteries. Strong ABS case uses special top-cap design that makes this a true maintenance free battery, completely eliminating leakage and acid spills. 12V. Cranking power range (depending on model): 110-340A depending on application. Weight: 7.7-19 lbs. Size range: 5.27"-8"×2.7"–4.8"×4.13"-6.7". Air-shippable.

For model/fit applications, see:

Battery applications by motorcycle model and year

Advanced battery technology that works much better (and longer) than even the best conventional lead acid batteries. These batteries are more powerful and dependable. Cranking amp ratings are double to triple regular types. They have an 8 year design life, an ultra long shelf storage life and a low self-discharge rate—after sitting for months (without any trickle charge) it’ll start. Deep cycle reserve power provides sufficient amps for confident starts even when 70% discharged.

Odyssey batteries have superior vibration resistance, a tough ABS case, and are lighter, too. Air shippable and non-spillable “starved-electrolyte” design. Works right out of the box with no charging needed. The California Highway Patrol use these batteries because with the engine off they must run their flashing lights and radios. 12V 14Ah. Cranking power range (depending on model): 100-380A. Weight: 6-26 lbs. Size range: 5.43"–7.27"×3.11"–7.05"×3.98"×6.67".

Cannot ship internationally

For model/fit applications, see:

Battery applications by motorcycle model and year

Drop weight. Lithium technology with a tough carbon-fiber composite cases made these next-generation lithium-iron batteries weigh an astonishing 70-80% less than a lead acid battery. These advanced batteries recharge quicker than a conventional battery and hold a charge for an entire year without maintenance and with zero sulfation.

Environmentally friendly too with no explosive gasses during charging, no lead and no acid, just discharge and dispose when it reaches the end of a long service life (up to four times the life of a lead-acid battery). 12V 14-27Ah. Cranking power range (depending on model): 210-405A. Weight: 1.68-3.85 lbs. Size range: 5.83"-6.55"×2.6"-3.39"×3.46"-5.51".

For model/fit applications, see chart here.

For use when switching out or installing molex connectors. The Universal has both male and female ends for removing male and female molex connectors. The ATX remover has a male only end for removing ATX molex connectors or adding wire sleeves. Simply insert and push. Works a lot better than jamming a screwdriver in the hole or trying to dig the connector out with needle-nose pliers, only to find you’ve fudged up the whole nylon housing in the process. 3.75", 1 oz.

This pliers’ particular combination of jaw width and length, and fulcrum location make it the best we’ve tried for working with Molex connectors. Wire cutter gauge is adjustable with a thumb slide and the return spring locks closed for carrying. 12-24 gauge AWC wire.

A unique vibration proof and reusable wire connector system that delivers a superior connection to crimping. Simple to use, only wire stripping required. Wire ends are locked between opposing cone shapes when hand tightened, resulting in a positive, strong connection. Really strong. Impossible to pull apart, but they easily unscrew for roadside service or re-use. There are no metal parts and the internal electrical resistance is less than with crimp connectors. Patented and design protected seven ways to Sunday, naturally. Color coded bodies are super tough Nylon 66 resin. These are the ultimate reusable weather tight connectors, and a great way to wire electrical accessories.

A reliable, compact wire connector system that lets you organize electrical accessory connections cleanly. Unlike crimp style connectors, these can be safely undone and reconnected as needed, over and over. Recessed set screws. Dead front construction. Captive wire protectors. UL rated up to 10 amps and 12awg wire. 4 pole is 0.5"×0.5"×1.5".

This tool is the easy way to disconnect and work with Molex, H-D and similar multi-pin electrical connectors. Removes six sizes of pins from their nylon housings.

It’s easy to create clean and durable accessory wiring connections. This kit contains a useful selection of sizes for a variety of 12V electrical applications. There are three sizes of connector blocks and pins, each of which has male and female components. Wires are crimped to the pins (soldering optional) and then the pins clip into the connector blocks which are shaped to preserve polarity. The five small connectors take 20-24 ga. wire and are ideal for things like radar detectors or tiny LED voltmeters; the four medium size connectors take 18-24 ga. wire and are suitable for things like GPSs, radio receivers and those sorts of loads; and the four large ones take 14-20 ga. wire for connecting things like grip warmers, radio transmitters or extra lights. Includes instructions and thirteen connector sets plus several extra pins in each size. (92 pieces total.)

Designed for basic electrical tests, this digital multimeter offers reliable diagnostics for everything from measuring AC and DC voltages, checking resistance and continuity, and helping find elusive electrical gremlins. Test leads wind neatly around case for compact storage. This small, lightweight multimeter fits comfortably in your hand but is rugged enough to withstand travel use. 4.75"×2.75"x.75".

Diagnosing electrical gremlins is much more manageable with this handy circuit tester. Perfect for finding a break in any 6V, 12V or 24V circuit. Attached to the clear handle is a stainless steel probe ready to test bare wires, terminals or connectors. Heavy duty alligator clip is attached to tough, flexible wire. Illuminating handle light indicates live circuit between two points.

Completely sealed 20 amp switch with weather resistant coating and O-ring stem seal. Includes a stamped metal on-off indicator plate that fits over the 15/32" diameter, 3/8" long mounting stem and chrome plated handle. 8" wire leads. 12V. 1.25"×.75"×1.75".

Supply safe, fused power to accessory electronic devices. Uses four ¼" male blade connections for easy installation insert the best mini fuse (not included) to match the power requirements of each device. A clear cover with insulated O-ring provides protection and a water resistant seal. 15 amps per circuit. Fits almost anywhere. Simple is good. 3.2"×1.77"×1.5".

Easily organize electrical connections with this 4 position terminal block. Molded from UL rated 94 VO Thermoplastic with tin plated brass terminals and zinc plated #6-32 steel screws. Rated to 20 amps/150 volts max. 2.16"×.88"×.41".

This quality 120 piece selection of crimp connectors and terminals contains an ideal mix of individual items for 12V accessory wiring projects. Each metal crimp barrel is surrounded by a color coded, transparent, adhesive lined, heat-shrink tubing. When properly crimped and heated, the tubing shrinks and the adhesive flows creating a high quality environmental seal that prevents corrosion and provides excellent water and contamination resistance. These connectors provide superior protection from mechanical abuse, wire pullout and current leakage.

Handy kits that contain every size shrink wrap you need. Has over 100, 4" long pieces from 1/16"–3/8" diameter.

Practical kit includes eighty-six 6" pieces, in six useful sizes, of high quality, stable and flame retardant polyolefin tubing. Shrinks to half original size when heated. Sizes from 3/16"-1" wide. Black.

This BMW switch coil cord easily connects your vest or liner directly to the standard BMW accessory socket on your bike. (BMW Socket (#108) is available separately and requires additional wiring to connect to the motorcycle battery).

Additional Information/Resources:

Standard BMW power sockets. Requires additional wiring.

Standard hookup for Kanetsu Vests and Liners. Length 30".

Additional Information/Resources:

Standard BMW Plug. Requires additional wiring.

Connect two garments to a single power plug.

Additional Information/Resources:

Standard hookup for Kanetsu Vests and Liners. 10 A Fuse. Length 25".

Additional Information/Resources:

Standard hookup for Kanetsu Vests and Liners. Illuminated push button on/off switch. Stretches from 3'–6'.

Additional Information/Resources:

Connect to a standard power socket on your bike...or your car, snowmobile, etc.

Additional Information/Resources:

A connector wire with a standard power socket that fits a cigarette lighter/accessory plug.

Additional Information/Resources:

A coil cord for connecting the vest to the motorcycle. The ultimate in simplicity and reliability. Remains flexible in all temperatures. Stretches from 1.5'–5'.

For hard wiring your GPS, radio, or other accessories. No springs, so it’s not susceptible to vibrations. The 20A includes two fuses for Garmin GPS’s, and features a rubber dust cap. The 30A includes one fuse, and features a water resistant cap and about a foot of wire on each end.

Provides a flush mount DC coax jack panel with a spring loaded cover. The six inch coax plug cable allows direct connection to DC coax power output. This is the same coaxial connector used in all Aerostich QuiConnect electric garment power cords.

Quickly stow away excess cord for your earbuds, headphones, electrical wire, etc., with these handy wire organizers. Flexible, virtually indestructible, and useful. Set of 3; black, red, white. OK, that’s a wrap (sorry…). 75"×.9"×.25".

This rugged 12V panel mount cigarette lighter power outlet socket is fitted with a rubber dust cap to keep out moisture and road grime. Installs easily and securely into any 1.2" hole. 6" wire leads. 1.5"×2.5". 12V/15A.

Ziptie to any handlebar or frame tube for a dependable source of power with all electrical accessories that have a standard cigar lighter plug. Useful for radar detectors, cell phone chargers, etc. Weatherproof spring-loaded flip top cover keeps out moisture, grit and grime. 3"×2"×1.75", with two 12" wire leads.