QuiConnect 2 Switch Coil Cord Kit

We have been making this pretty neat coil cord power control for twenty years. I remember designing it to be an illuminated hi-low inline switch of such small dimension that it would not be a 'lump' in the middle of a compact coily power cord. We went round-and-round trying to find a switch which would allow a better functioning and packaging design. Something tactually, visually, and ergonomically lighter and cleaner.

And there still isn't anything as good in terms of simplicity and overall handy-ness. I wanted this cord switch to be so easy to use one could forgo a thermostat. They always seemed useless over-complexity...even the newer nice digital ones everyone uses now (just yesterday all were stupid power-hungry inefficient resistance rheostats). I'd used one several times but wanted something thoughtlessly simple, super-compact and field-reparable if ever needed. (This last consideration turned out irrelevant.)

It's just too easy to be riding along and without looking down move my left hand downward from the grip momentarily to find the cord lying across my left thigh and then by touch alone (finger or thumb) push or release the illuminated in-out button…then move my hand back to the left grip.

It's only one second, done without thinking, and there's no fumbling around. I can feel at a touch if the button is in high or low position to maintain temperature at a nice level all day long, with neither thought or effort. Just click-on and click-off as needed for comfort, and if there's ever question about power status a quick glance down shows the red pilot light glowing on or off through the button's cap. Even in daylight.

So today if I were for some reason forced to use some non-Aerostich electric garment, I'd still want this simple, intuitive and reliable coil cord and switch.

-- Mr. Subjective 12-13

If you have a BMW with a built-in BMW accessory socket, then the BMW-style connector is simple, easy and good. Otherwise we recommend the Quickconnect, also known as coaxial or 'male-and-female' style. It's the easiest to use (to connect and disconnect) and has lowest electrical resistance, so your gear heats up a little faster. (A nanosecond? Half a minute? In use we can't feel any difference, but we once did some controlled bench tests and there is a difference.)

There are zero reliability issues with all styles. All are tough and durable in all weathers and conditions. The SAE (Society of Automotive Engineers) style is the commonest and oldest design, and it's the hardest to push together and pull apart, but this gets slightly easier as it breaks in. It's also the least expensive to manufacture, and is the most widely available at auto parts stores.

The BMW style has one feature the other two don't...It comes apart with a screwdriver. Inside are two little set screws, one holding each wire to it's respective terminal. These make it simple to transfer the plug to another wire if anything does break. This style is slightly larger and bulkier, and by a small margin it's the easiest to manipulate wearing bulky insulated gloves.

But we still prefer and recommend the durable, compact and easiest-to-use Quickconnect coaxial style. Overall, it's the best.

-- Mr. Subjective, 12-13

Heated Gear Power Cord Port

This hidden cord port is part of all one piece Roadcrafter Classics and R-3s. It's a pass-thru for a short wire that connects any electrically heated clothing to the outside of the garment. The other side of this pass-thru is inside the slash pocket located behind the lower flapped pocket on the left side.

How it works is you position either a coily power cord (#172) or jumper cord (#162) so the end of the cord that connects to the electric garment is dangling out of this port on the inside of the suit. The other end is 'stored' in the slash pocket that forms behind the lower left flapped pocket on the outside of the suit.

When you are ready to ride somewhere with an electric garment beneath the suit, you first put on the electric garment. Then you put on the suit. Then you connect the power cord or jumper cord to the electric garment. Then you zip the suit closed around you. Then you get on the motorcycle (or stand close to it) and remove the other end of the cord from the slash pocket located behind the flapped pocket and plug it into the power on the motorcycle. Then you ride away warm and comfortable.

Photo courtesy of John Blowitz: